Ok Ok, Trying to get the ship ready for the season AND write about it is kinda crazy so this is going to be quick.
The COLUMBIA III comes out of the water every year for at least a minimal wash, inspection, anti-fouling paint job, and replacement of zincs. In boater talk this is called “a shave and a hair cut.” Other years require more in-depth procedures like pulling the rudder off and drive shaft out for Transport Canada to inspect. But this was an “off year” and therefore a smaller work load for me. Except, that is, that I cut my bow iron off.
As I say every year, I NEVER like seeing the COLUMBIA III lifted high out of the water, “It just don’t seem NATURAL!” And I never really relax until she is safely back in the water again.
Here she comes out and I have my first peek at her undersides since last May, 2018.
The first order of business was for me to sand the water-line gumwood. It seems like the ship is 150 feet long when I am holding a heavy sander up on the top of a step ladder. Add the poor visibility of a face respirator and you have all the makings of a fun few days!
Here’s a quick step back in time . . . another project was to make a mount for a new transducer for a second sounder. This will enable me to have sea water temperature readings in the wheel house. Cool and useful for research tracking for the local First Nations . . .
and here is the finished product. I think this particular job required at least 87 trips between the chapel bilge on the INSIDE of the vessel, up the internal stairs, out the door, along the side deck, down the 15′ shipyard staircase and crawl on my hands and knees to the point on the OUTSIDE of the hull where the new transducer was going to go . . . . only to realize I’d left the wrench I needed back inside . . . it’s good exercise working without a helper on the INSIDE.
and then new bow iron . . . . It is always good to remain flexible . . .
I had planned on having the bow iron made out of regular steel. This would require the iron to be fabricated in place on the ship, then removed and shipped to Vancouver to be galvanized and then reinstalled on the ship . . . But after a whole day with two welders attempting to make the iron in mild steel, the welders vetoed my plan. They felt there was no way to make the iron in place that would not cause it to spring inwards upon removal for galvanizing. They felt I would never get the iron back onto the ship. So they suggested I switch to stainless steel that they could form and secure in place on the ship. So, on day two they started again. Here they ran a new SS bar down the stem and tacked the side plates on.
There was much bending, prying and trimming before I added many, many tubes of Sika FLex sealant to the hull before the plates were welded into place. I was able to locate the forward most oak rib in the for’csle and I ran 1/2″ SS bolts thru to pull the side plates against the hull. It was satisfying to see the sealant squeezing out along all the edges. These bolts were then carefully welded in place and the nuts cut off leaving a flush but secure fastening. The 1/2″ x 5″ SS lag screws that hold the bar against the gumwood stem were also welded in place and ground off flush after.
The existing portion of the bow iron that was well below water-line had not deteriorated and the new SS sections were welded into the lower portions of the existing iron.
And the boot top!!! . . . The shipyard crews were supposed to do the waterline detail but they were too busy . . . . so I did it myself. I do love working on the tippy top of a step ladder . . . Here’s a dusty me, getting the water line ready . . .
and taping the waterline . . .
and painting the black boot-top stripe . . .
I also painted the draft marks carefully. . . . very carefully! The gumwood was sanded and refinished as far up as I could reach standing on the top of a step ladder. The rest can be done from a paint float in the boat shed. Starting April 1st.
Oops! . . . . how did this picture of my grand-daughter, Maeve, slip in here .. . . .?
The new bow iron in all its glory! The best part about the new stainless steel bow iron is that now, when the swinging anchor bumps the bow iron, it will not chip off the zinc coating and it will not rust!!!! YAY!!!!
And one week ahead of time, (because I didn’t need to ship the bow iron to Vancouver to get galvanized) the COLUMBIA III slipped back into the water.
And I am finally home. Shipyard alone is a lot of work for me. Now to get ready for the REAL work to begin with the crews, April 1st! But that’s the next post . . . . .